|Top Previous Next|
What's New in the Latest Version
•Bug fix: due to a problem during installation, when the user enabled a show they might get an error stating ”Shows cannot be enabled because of an error. ActiveX component can’t create object/LORMonitor". Also, LORHub may crash when trying to create an SD card.
•Added an option for the Text motion effect to display smooth (anti-aliased) text.
•Restored the ability to left, center, or right justify text in the Text motion effect. This setting only applies when there is more than one line of text.
•A light bulb icon is now displayed in the lower right corner of the Sequencer -- on the status bar. It will be dark when control lights is off, and bright yellow when control lights is on. This way the user can know the light control status without having to open the Control Lights panel.
•When running the demo version of the Sequencer and then registering, the Control Lights panel did not update. The Control Lights check box was still disabled and the message "Controlling lights requires a license" was still shown.
•After any Paste operation in the Sequencer, all of the cells that were pasted into should be selected. However, after a Paste Special with the Flip Vertical option enabled, the paste would work correctly but the wrong selection would be shown.
•The Light-O-Rama installer process and installer executable have been updated:
•This should eliminate some installer errors such as files not being cleaned from the LOR Programs directory when installing new versions.
•The installer size has been reduced by approximately 20 meg.
•Previously the DirectX installer was always called regardless if a machine needed DirectX 9 installed or not. Now only machines that need to have DirectX will execute the install.
•Additional files are now electronically signed by LOR to ensure their authenticity. This will allow Windows to prompt the user to obtain necessary permissions.
•The installer will now place a shortcut on the users desktop to start the LOR Control Panel. At the end of the install, you will be asked if you want to start the control panel. This should help new users get started using the software.
•The installer will not run on older Windows machines. You must have Windows 7 or newer as per the requirements of the software. Previously the software could be installed, but some programs would not work.
•When starting the Control Panel for the first time, users will be shown a new screen that briefly describes how to use the control panel and software. Again, this is an effort to help new users get started.
•Note: Should you have any issue with the new installer process, first uninstall any LOR programs, then run the LOR Registry Wipe and then re-install. This should fix most installer issues. Please contact the help desk if needed.
•New motion effects added: Spinner, Spin Fade, Archimedes Spiral, and PictureXY. Spinner, Spin Fade, and Archimedes Spiral should work especially well on pixel-based stars, spinners, wheels, and snowflakes that use a Custom shape. PictureXY is a simplified picture effect that gives you direct control over image size and placement.
•Pinwheel: the rendering quality has been improved and a new color mode has been added (multicolor arms).
•Picture: added a "Numbered Sequence" check-box. Prior to this version, image sequences were detected automatically. Now they are indicated by checking the new box. If you have an existing sequence that uses numbered image files for an animation, your sequence will no longer work as originally intended until you reopen the sequence and update the applicable Picture effects.
•Color Wash: added dither and gradient options. Also, a small change was made to the "fade left to right" and "fade right to left" options, as they did not produce symmetrical results The same applies to the "fade top to bottom" and "fade bottom to top" options. This was only apparent on very small props.
•Fire: fire can now emanate from any or all sides. It was also fixed so that it now works with the "Alpha Blend" mixer mode.
•When setting colors in the Motion Effect Generator, "transparent" is now an option. This is useful in the "Alpha Blend" mixer mode and when motion rows are combined using the new "overlay" mode (see below).
•In the Add/Modify Motion Rows dialog, you can now specify how the rows are merged together during rendering:
•Blend: the maximum brightness for each pixel is taken from the effects across all rows -- backward compatible with prior versions, including the S4 Pixel Editor.
•Overlay: rows are overlaid one on top of the other using alpha blending (i.e. effects can have areas that are transparent). The first row listed in the dialog is used as the background, then successive rows are layered on top of it. Note that you can use the dialog to change the order of the rows, thus changing the order in which rows get overlaid.
•In the Paste Special dialog:
•you now have options to flip the pasted data horizontally and/or vertically
•you can now override the Paste Mode shown on the toolbar from within the dialog
•the maximum number of times a clipboard can be repeated horizontally or vertically was increased from 100 to 10,000
•repeating vertically to the end of the sequence is fixed
•Added the ability to embed files for the Picture Effect inside the sequence file. This makes it easier to move sequences from one computer to another because you don't have to also transfer the associated picture files. Use the new menu item Sequence > Manage Picture Effects.
•Added the ability to import xLights model files (.xmodel) into Preview Design. This capability is limited to custom models.
•In Preview Design, bulb transparency can now be applied to any bulb shape.
•SuperStar now supports audio files with a sampling rate of 48,000 as well as the standard 44,100 sampling rate.
•In the Sequencer, when adding new SuperStar effects to a group, the effects did not render correctly.
•Closing a sequence before the initial calculations had finished (wait icon was still spinning) could cause the Sequencer to crash.
•In the Sequencer, after importing an LPEPROP file into Preview Design, the Channel Conflicts tab was not updated.
•In the Sequencer, removing channel level from a pixel-based prop did not cause the playback on the screen to be recalculated.
•In the Sequencer, when selecting props for a new grid view, clicking a check-box did not highlight the prop name; so if you subsequently used the up or down arrow keys to navigate the list, the wrong item was selected.
•In the Sequencer, after stopping playback in an animation sequence, the ribbon's Waveform button would get enabled.
•In the Sequencer's Motion Effect Generator, the drop-down to select an effect would sometimes pause before opening.
•In the Sequencer, when the "RGB Split" Sequencer preference was enabled, pasting into a collapsed group of RGB channels would produce the wrong result.
•In the Sequencer, when the "RGB Split" Sequencer preference was disabled, pasting from a legacy clipboard file (one created with S4 or earlier) into RGB channels would produce the wrong result.
•When the Sequencer window was minimized and you used Windows File Explorer to open a sequence that was already open, the pop-up message stating that the sequence was already open could get stuck behind another window, requiring that the Sequencer be force-closed.
•In the Sequencer, starting to play a sequence while control lights was enabled could result in a message window being displayed that was larger than the screen (if there were props with motion effects that used LOR networks that were not enhanced).
•The Copy function in Preview Design will no longer create props beyond the limits of the design canvas. Also, you can now Undo the results of a Copy.
•The status bar now shows the current selection mode: cells, effects, rows, or freeform.
•When starting a new show, there can be a slight delay of up to 2 seconds before the first sequence starts to play. During this time, heartbeat messages were not sent to controllers allowing them to possibly loose synchronization. If the controllers lost sync, approximately the first second of the first sequence could be lost while the controller re-synchronized with the MP3 director.
•When running in Enhanced mode, which does not support LOR Advanced commands like Twinkle and Shimmer, the controller could unexpectedly place channels into Shimmer or Twinkle mode. For LOR160xg3 controllers this is fixed in Firmware 1.17. For CTB16PCg3 controllers this is fixed in firmware V1.10. Only G3 controllers support enhanced mode, so other controllers do not need to be updated.
•When creating a Simple PC show in Hub, the time entry form incorrectly allowed for typing in a start or end time. This could lead to incorrect start/end times being displayed and scheduled shows not starting/ending properly.
•When creating an SD card show in Hub for G3 or later MP3 directors that had 2 or more ports with firmware 5.36 or below, the files created did not have the correct extension.
•In the Hardware Utility it was still possible to configure and change both DIO boards and X-10 settings. Support for both was removed for S5. The contents of these tabs has been removed, and the tabs themselves will be removed with a later release.
•On the Sequencer's Prop Definition screen, pasting invalid data into the Unit ID or Circuit fields could result in a weird error message or a crash.
•In the Sequencer, added a preview check to ensure only groups with arrangement of 'none' can contain members that are groups with an arrangement of 'none'. http://forums.lightorama.com/topic/51061-arithmetic-overflow/
•The Sequence Compressor tool now handles shows that contain S5 sequences (LOREDIT files). You can also select an LOREDIT file when compressing a single sequence. This can be used to prepare an entire show for playback before its scheduled start time.
•In the Sequencer, the program could hang when inserting a SuperStar effect on top of an existing Motion Effect.
•In the Sequencer, inserting SuperStar effects on motion rows that use only some of the pixels of a prop or group (i.e. a subsection) was not working correctly.
•When playing a sequence in a show, performance was improved for channel effects on DMX networks. For sequences with many channel effects on DMX networks, you will want to regenerate the playback files. Use the Sequence Compressor with the "Force Compression" option enabled to do this.
•In the Motion Effect Generator, there is a new button that allows the user to reset all of an effect's parameters back to their default values.
•Users now get a warning if they are about to overwrite existing SuperStar effects with a new SuperStar effect.
•Users now get a warning if they try to insert a SuperStar effect that is less than 1 second long.
•When creating an SD card in Hub, if any time (scheduled start or end) started with '12', the time could be incorrectly set in the SD card configuration file. The show would not then start/stop at the correct time.
•When creating an SD card in Hub, if you were using an S5 Filler, Hub would correctly call the conversion of the file to S4 but then would validate the 'start' sequence file name. If a start file did not exist, Hub could then crash.
•When creating an SD card in Hub, while creating a new show on an new SD card show, if a SHOW01.CFG file existed on the SD card AND that configuration didn't actually contain any sequences, Hub would still attempt to use it even though it was not valid. Later on, Hub would attempt to use the bad configuration and in some instances crash.
•When creating an SD card in Hub, the program was not checking to see if any error was returned from the S5 Sequencer pre-process. If an error was returned, and depending on what the error actually was, subsequent calls to the Sequencer from Hub could be made to functions that were not initialized and hub could crash.
•In the Sequencer, users with a demo license for SuperStar could not save effects to a motion effect row in the Sequencer.
•In the Sequencer's Prop Definition screen, added validation when entering a start circuit/channel to prevent a crash.
•When running the Sequencer for the first time after a fresh install, the user would get this erroneous message ‘The master list of previews, palettes or motion effect favorites has been changed by an external program. Restart to load the updates.’
•In the Sequencer's VU Wizard, moving the threshold slider is now more responsive
•Motion effects that respond to the music (musical note icon next to the slider) worked correctly in the Sequencer, but not in the Show Player or when written to an SD card.
•In SuperStar, the name of images could revert back to "image xx" after doing "manipulate images".
•In SuperStar, a degree symbol in the image name would cause the sequencer to fail to save the file.
•In SuperStar, increased allowed DMX size from 100 to 200.
•In SuperStar, added the ability to add or subtract from color values in an image by pressing the '+' or '-' key while clicking on image pixels
•In SuperStar, when servicing a SuperStar Request, if we fail to load the data file then display a "failed to read file" error.
•On some Windows Systems, usually but not limited to Windows 7, the LOR Show Player would crash upon trying to start a show. When it crashed, the LOR Control Panel would attempt to recover and restart the Show Player. This would cause the Show Player to loop on these machines and not actually play a show.
•In the Sequencer brightness adjustment on the Playback window was disabled when the background image was embedded with the preview.
•In the Sequencer the title bar of the playback window showed "Playback stopped" during playback after a sequence loops and continues to play back.
•In the Sequencer new sequences lose motion effect rows with "custom" subsections that were defined in the preview. Custom subsections appear often on props loaded using the Boscoyo import. http://forums.lightorama.com/topic/49712-motion-effect-rows-disappear-536
•In Preview Group Definition, there is a new arrangement setting of "custom". When set, 2 additional columns (TOP and LEFT) will appear in the group definition grid. This allows you to specify where each prop is placed in the effects buffer for the group. This is especially useful for SuperStar users with complex layouts. http://forums.lightorama.com/topic/47742-matrix/
•New Chase option: Same Row Type. If selected, the chase will only occur on rows of the same type as the first row. For example, if the first row is a regular channel, any RGB channels or motion effect rows will be skipped. If there is no check mark next to this option, then the chase will proceed through all selected rows, regardless of type. Requested by Drew Hickman.
SUPERSTAR EFFECTS STORED USING THIS VERSION OF THE SEQUENCER CANNOT BE LOADED INTO PREVIOUS VERSIONS OF THE SEQUENCER.
•Added a "Change Orientation" section to the Move or Scale Selected Effects dialog. It changes a sequence from vertical to horizontal or horizontal to vertical.
•Added the "Prorated" button to the "Manipulate Selected Images" dialog box. Rotation Angle, Brightness, Move, and Scale can be applied the same to all images, or can be "prorated" across the selected images.
•Added "Clip Rectangle" as an option in "Move or Scale Selected Effects." Previously if you moved or scaled effects it did not move or scale the clip rectangle. Now, if "Clip Rectangle" is selected "Move", "Scale", and "Change Orientation" change the clip rectangle as well.
•In the "Image Setup" dialog box "Rotation" has been added as an option for an Image Action. Rotation can be 0, 90, 180, or 270.
•The firmware for the N1uMP3g4 MP3 Director (One Network, Black Plastic Case, Generation 4) has been updated to resolve an issue which caused the director to sometimes lock up on boot, as well as an update to fix issues with trigger inputs.
•In the Sequencer, when assigning a different preview to a sequence and there were preview groups that share the same name in the old and new previews, the new groups would not render effects until the sequence was closed and then re-opened. Reported by Drew Hickman.
•In the Sequencer, when changing the shape of a prop in the Prop Definition screen, parameter values will no longer revert to their default values when the parameter for the prior shape and the new shape have the exact same meaning.
•In the Sequencer, when upgrading a legacy sequence to S5, RGB channels would not import unless the "Split RGB" Sequencer preference was enabled. Now they will import correctly regardless of the preference setting.
•In the Sequencer, if a secondary monitor has been unplugged since the time the Sequencer was last run, any floating windows on the secondary monitor will now be re-positioned onto one of the remaining monitors. Reported by user TitusCarnathan. http://forums.lightorama.com/topic/49700-tc-73-playback-windows-disappears/
•In the Sequencer, when a prop used the Tree 360 Up & Over shape with pixels and a starting location that specified a clock-wise wiring order, the pixels were offset by 180 degrees in the effect buffer. Reported by Drew Hickman.
•In the Sequencer, when adding an LOR device in Preview Design, if you entered a name and then changed the device, the name you entered would get overwritten. Reported by user ndutton. http://forums.lightorama.com/topic/49762-automation-bugs-in-prop-generation/
•In Superstar, fixed a bug where the Clip Rectangle was not being drawn when in Image mode. This bug was introduced in the previous release when drawing in image mode was optimized.
•In Superstar, fixed a bug where a large grid with 100 ribbons or more would not create a scene using ribbon 100
•In Superstar, fixed an issue where creating a 7 tier, 360 degree of traditional lights could cause a crash.
•A new Sequencer Preference on the Channel Effects tab controls whether an RGB channel is displayed with its red / green / blue sub-channels or not. Turning this option off can save memory, allowing larger sequences to be loaded. Requested by user dougd. http://forums.lightorama.com/topic/49460-reverted-back-to-524
•You can now specify a "default paste mode" on the Startup Tab of Sequencer Preferences. The Default Paste Mode will be shown whenever a sequence is opened. Requested by user User dgrant. http://forums.lightorama.com/topic/49611-editor-preferences/
•On Preview Design's Channel Conflicts & Bulk Changes tab, you can now use the "Set LOR Network" and "Set DMX Universe" to change props from LOR to DMX or vice versa. Changes were also made to the "Select All" check box on this tab to make it more intuitive.
•On Preview Design's Design tab, you can now choose to save the background image with the preview (see the Background tab). If you export such a preview and send the export file (LORPREV extension) to someone else, the background image will be included. The background image will also be included if you send a sequence to another user and the sequence uses such a preview.
•Added "rotation angle" to the "Manipulate Selected Images" dialog box.
oIf one image is selected then it sets the rotation angle of that image
oIf more than one image is selected, the angles get applied proportionally to each image. For example, if you selected 4 images and apply 33 degrees, then 0, 11, 22, and 33 degrees get applied to the 4 selected images.
•When nothing was set in Network Preferences, it was possible for the Sequencer to initialize with the Control Lights box checked and no obvious way to turn it off. Going forward, when nothing is set in Network Preferences the Control Lights button will be unchecked, and a message will remind the user "Network Preferences must be set before you can control lights". Reported by Drew Hickman.
•In the Sequencer, when you created a prop with the custom shape using version 5.3.4 and earlier, the autonumber function had a maximum value of 16,000 and would crash when it tried to insert 16,001 in the custom grid. Going forward, the maximum value has been increased to 999,999 and the program will not crash if you exceed that number. Reported by Jeff Banbor via the help desk.
•The Sequencer could crash when clicking on a motion effect in the grid or when opening the Motion Effect Generator. Reported by Jeff Banbor and others.
•In the Sequencer, in certain situations, clicking any of the play buttons on the Playback Window would result in a message of "Unable to Start Playback", whereas the play buttons above the sequence grid would recalculate data and then start playing the sequence. Reported by user stevehoyt. http://forums.lightorama.com/topic/49605-unable-to-start-playback/
•In Superstar, the progress dialog box was not updating.
•In Superstar, enhanced the "Set group time range" button on the toolbar so that it proportionally sets the start and end time of all selected effects. This is particularly useful if you have a bunch of adjacent image actions and want to change the time range of the entire group.
•Added a text filter to the Online Prop Import dialog, so you can filter the listed props by their description. Requested by Light-O-Rama.
•The timeline now uses a little less vertical space, and is displayed with a better font. Requested by Light-O-Rama.
•Converted the "Timing" select action to a lock icon on the timing grid toolbar. This allows a user to create effects and adjust timing marks without having to go back and click on the toolbar. Requested by Drew Hickman.
•Added a new playback marker style: show moving marker and highlight timing marks. Selectable in the Playback tab of Sequencer Preferences. Requested by users at Christmas Expo 2019.
•The portion of the toolbar related to the timing grid can now be positioned on the left or right side by right-clicking anywhere on the top toolbar and picking an option from the pop-up menu. Requested by users at Christmas Expo 2019.
•Clicking an effect "Type" button on the toolbar will automatically change the select action to "Create". Requested by users at Christmas Expo 2019.
•In the Sequencer, resizing the Effect Samples window when color favorites are displayed can cause the color samples to be redrawn incorrectly (stutter pattern). Reported by Light-O-Rama.
•In the Sequencer, with license levels of Advanced or below, the Color Favorites buttons at the top of the Effect Samples window do not wrap around if the window is too narrow to display them all. Reported by Light-O-Rama.
•In the Sequencer, disable the background brightness slider on the playback window when a motion effect is playing, or if the sequence's preview doesn't have a background image. Reported by Light-O-Rama.
•In the Sequencer, tick marks on the timeline and timing marks on the sequence grid were misaligned by 1 pixel in many cases. Reported by Light-O-Rama.
•In the Sequencer, subsequence names were not being displayed on the grid. Reported by users at Christmas Expo 2019.
•In the Sequencer, when creating color fade effects, the Slope setting is now taken into account. The "O" shortcut key simply selects the Color Fade effect type on the toolbar, it doesn't actually create an effect. To create color fade effects with shortcut keys, use "A", "I", "D", and "U". Reported by users at Christmas Expo 2019.
•When playing a show or creating an SD card, fixed issue with playback file creation checking the preview revision. As a fix, the preview revision number is now part of the playback file name. Reported by user default. http://forums.lightorama.com/topic/49511-bug-report-pm02-show-player-processes-all-files-and-updates-playback-files-every-time-it-restarts-even-if-the-base-files-have-not-changed/
•On a very limited number of computers, LOR Hub could refuse to open and/or crash with a runtime error 50003. This error was related to certain graphics used in the application, and those graphics have been replaced. Many thanks to Monty C. for helping us track down this issue.
•When creating SD cards with LOR Hub using Sequencer '.loredit' files, Hub would refuse to create the card with a generic 'There was a problem creating your SD Card' error. Hub was improved to display a more descriptive error, and the bug preventing the creation of the SD cards was fixed.
•In Superstar, if you have two screens with the main screen in one monitor and the sequencing grid in another monitor and the main screen is shorter in height than the grid screen, then the click and drag drawing in image mode on the grid screen stops working when you go beyond the height of the main screen.
•In Superstar, scene elements with a Y coordinate beyond 128 were not working.
•In Superstar, when adding images from a gif, it was not remembering the rotation angle.
•In Superstar, "image" now works in group modify.
•In Superstar, fixed it so you can use "large grid" in the "image setup" dialog box when superstar is launched from the S5 Sequencer. Also allow setting the size of the "large grid".
•In Superstar, optimized the "click and drag" drawing speed on the green sequencing grid so you can more easily draw images on pixel grids with large numbers of pixels.
•In Superstar, improved layout of green pixel grid so it fits onto the screen for large numbers of pixels.
•In Superstar, changed the terminology for the license level from things like "2_CCR" to "100_pixels".
▪In the Sequencer, the user now has a choice of displaying the tool buttons along the right side of the grid, or immediately above it. User can right-click in the tool button area to access available display options. Reported by user PhilMassey and others.
▪In the Sequencer, a new select action of "Timing" has been added. It replaces the "Lock Timings" option that was present in a couple of menus in prior versions. The new Timing button is only enabled when a Freeform Timing Grid is selected. If the new Timing button is selected, then timing marks are unlocked and right-clicking on the grid opens directly to the Timing Mark menu. For any other Select Action, timing marks are locked, and right-clicking on the grid opens the context menu present in previous versions (Timing Mark is a sub-menu). Reported by user PhilMassey. http://forums.lightorama.com/topic/49037-thoughts-on-s5/
▪Sequencer bug fix: when chasing an RGB color, for example green, the chase becomes white when the chase crosses from one grid view group to the next. Reported by user PhilMassey.
▪In the Sequencer, you can now right-click on the toolbar that includes the playback buttons to set the maximum size of the buttons. Choices are: large, medium, and compact. Reported by Drew Hickman.
▪When dragging effect edges in the Sequencer, if you drag the beginning of an effect to the right past the effect's end, the effect will now be deleted. Similarly, if you drag the end of an effect to the left past the effect's beginning, the effect will be deleted. Reported by Drew Hickman.
▪In the Sequencer, when the motion effect source is set to "Samples", the Effect Samples window will be made visible if it is hidden. Reported by Light-O-Rama.
▪Sequencer bug fix: after modifying a preview, you might get the following error while opening a sequence: "An entry with the same key already exists". Reported by NJ Malenke via the help desk.
In previous versions of the software, you could not directly schedule, load to a controller (stand-alone mode), or create SD cards with native (IE .loredit) files. Instead, you first needed to create legacy files (IE .LMS or .LAS - sometimes referred to as 'playback files'), and then use those. The suite can now instead take native .loredit files for all of these functions without the need for manually creating 'Playback' files, and use them directly.
LOR Hub, LOR Show Editor, and LOR Hardware (stand-alone loading only) can now accept native S5 files.
With the newest generation of LOR MP3 directors (Generation 4), some directors have the ability to be 'linked' together - allowing for a show with an almost unlimited number of networks or DMX universes to be run from these directors.
LOR Hub is required to create the SD card sets for linked directors, and you must use the Advanced SD Card Wizard to create them. N4G4 Directors require at least firmware version 6.2 to use director link.
New firmware for N4G4 directors has been released to support Director Link mode.
LOR Hub has now taken over all SD card creation tasks for MP3 directors. In the future, the SD card creation process that is available in the LOR Hardware Utility will be removed. You should be using LORHub for ALL SD card creation tasks.
A new feature has been added to auto-sequence singing faces in SuperStar..
Added new parameter to the Meteor motion effect called "Speed Mode". Speed mode has 2 values: "pixel rate" uses the existing fall rate calculation; "scaled rate" will cause meteors to fall at a rate that scales with the size of the prop. Requested by Light-O-Rama.
Added a new parameter to the Meteor motion effect called "Drop Mode", which adds new patterns to meteor drops (in addition to the existing random pattern). Requested by Light-O-Rama.
Added new option to fill corners on the Marquee motion effect. Requested by Steve Warner.
Added additional options to pre-scale an image in the picture effect: fit-to-width and fit-to-height -- which maintain the image's aspect ratio. Also increased maximum horizontal and vertical scale values from 100% to 400% so images can be stretched if needed. Requested by Steve Warner.
Added movement options to the Picture and Text effects that are essentially the second half of the Peek-a-boo movement. The options are: reverse, exit_left, exit_right, exit_top, and exit_bottom. Reverse is the default and replicates the functionality of prior versions. Requested by Drew Hickman and user Little_b.
Added ability to adjust red level, green level, and blue level independently in the picture Picture effect. Also added the ability to adjust transparency of the picture. Requested by Light-O-Rama.
Made picture and movie effect references stored in a sequence file relative to the sequence directory. This makes it easier to move the sequence to another computer, as long as the picture and movie files are stored in the sequence folder or in a sub-folder below it. Implemented in response to a help desk ticket.
You can now select S5 sequences (LOREDIT extension) when creating a show. They can also be selected when creating an SD card in LOR Hub. Playback files are now created and updated automatically behind the scenes. "Create Playback Files" has been removed from the Sequencer File menu, as it is no longer needed. Requested by Light-O-Rama.
The motion effect toolbar button has been combined with the motion effect selection window. Now, when the motion effect toolbar button is selected, the motion effect tool window will open; and when another toolbar button is selected, the window will close. This works in a similar manner to the Color Fade tool. Requested by Light-O-Rama.
Added the ability to drag the ends of channel and motion effects to adjust timing or create a fade. This feature is enabled or disabled by clicking on a new toolbar button next to the "nudge" tools. Requested by Light-O-Rama.
On the toolbar, the channel effect selection has been changed from a drop-down, to a series of buttons. A new "foreground" button allows you to change the intensity of existing effects. Requested by Drew Hickman.
Changed the preview name on the toolbar from a drop-down menu, to a button. Now clicking on the preview name takes you directly into Preview Design. Requested by Light-O-Rama.
The preview name is now displayed on the toolbar in a fixed width box, so that toolbar button location won't vary based on the length of the preview name. If the preview name is longer than the box, you can hover your cursor over it and a tootip will the full name of the preview will be displayed. Requested by Drew Hickman.
Moved audio wizard items on the main menu from the Sequence menu to the Tools menu (to be more consistent with the S4 Sequence Editor). Menu items have also moved one level up, so they take one less click to access. The audio wizards can also be accessed from various context (right-click) menus -- and those remain unchanged. Requested by Drew Hickman.
Converted the right-click menu of the playback window (play, stop, and background image brightness) to a toolbar, to make it more user-friendly. Requested by Light-O-Rama.
Increased the number of tiers on a "Tree 360 Panels" shape from 12 to 25, and added a pixel offset parameter for each tier. Panels with traditional lights are now supported. Requested by Drew Hickman.
"Tree 360 Wedges" using traditional strings (megatrees) will now display their channels in the correct order when a sequence is first created. Requested by Drew Hickman.
Megatrees and segmented arches with traditional strings will now avoid the r/c nomenclature in their names and instead use "string" or "bundle". Requested by Light-O-Rama.
In File References, allow the user to change a file name, not just a directory. Requested by Light-O-Rama.
In prior versions, space-bar playback moved the selection when stopping, but clicking the stop button on the toolbar did not. Now, clicking the stop button during playback will also move the selection (like the S4 Sequence Editor). You can prevent the selection from moving by shift-clicking on the stop button. Requested by Drew Hickman.
Changed "Unit #" to "Unit ID" in Prop Definition dialog to be consistent with controller documentation. Requested by Light-O-Rama.
On the "Channel Conflicts & Bulk Changes" tab in Preview Design, renamed the "Renumber Strings" menu item to "Reorder Circuit/Channel Numbers". The new name better reflects the function. Requested by Light-O-Rama.
On the "Channel Conflicts & Bulk Changes" tab in Preview Design, added the "Add Leading Zeros To Numbered Prop Names" menu item. Any selected props that have a number in their name will have leading zeros added to the number. This can aid in sorting the props in the desired order on the sequence grid. Requested by Light-O-Rama.
On the "Channel Conflicts & Bulk Changes" tab in Preview Design, added the "Replace Text In Prop Names" menu item. This function gives you the ability to search for and replace text in prop names, just like you would in a word processor. Requested by Light-O-Rama.
Added ability to sort the current grid view. Sort option is on the grid view menu. Requested by Drew Hickman.
Added ability to sort channels by physical channel settings. Requested by Drew Hickman.
When opening the motion effect generator with more than one motion effect row selected, you will now get an error message. Also, when editing a motion effect in a sequence, you can no longer change the prop/group drop-down. Requested by Drew Hickman.
When the toolbar tool is set to Motion Effect or SuperStar, the cursor is now sensitive to the type of row it is over and will only display the pencil cursor when over a motion effect row. Requested by Drew Hickman.
Improved the display of Motion Effect thumbnails for the built-in effects. Requested by Light-O-Rama.
The SuperStar toolbar button now has an option to always apply the effect to the entire row. Requested by Light-O-Rama.
The "Add/Modify Motion Effect Rows" dialog is now resizable, along with other tweaks. Requested by Light-O-Rama.
Importing Boscoyo props will now create Motion Row Defaults where they exist in the Boscoyo data (e.g. Chroma Bulbs). Requested by Light-O-Rama.
Added ability to create and edit custom motion effect subsections (subsections no longer have to be rectangular). Requested by Light-O-Rama.
Made it easier to start dragging timing marks on the grid -- the mouse pointer no longer needs to be directly over the timing mark, it can now be within a few pixels of it. Requested by Light-O-Rama.
The motion effect and SuperStar buttons on the toolbar are now disabled when the current grid view does not contain any motion rows. Requested by Drew Hickman.
If have a Pro license: after changing the preview assigned to a sequence, if there are pixel-based props without a motion effect row, you will be asked whether you want to add a motion effect row to each of those props. Requested by Light-O-Rama.
The sequence file name on the tab header had an asterisk suffix when there were unsaved changes in the sequence. However, being at the end, the asterisk wasn't always visible. So the asterisk indicating unsaved changes has been moved to the front of the file name. Requested by Light-O-Rama.
When selecting a region of the grid using the mouse and you reach the grid's edge, the screen will start automatically scrolling. Now the scroll speed will increase the further outside the grid boundary you get (like SE). Requested by user dgrant.
For LOR Sequencer:
The pencil cursor now scales with Windows scaling. Reported at Expo 2018.
After selecting "Add/Modify Motion Effect Rows" and then changing the size of a row's subsection, then clicking OK to close the dialog, the preview did not recalculate and display effects using the new subsection size. Reported by Light-O-Rama.
"Add/Modify Motion Effect Rows" and "Delete Motion Effect Row" (and a few other entries on the Item List's right click menu) are now disabled while calculations are running, as this could cause data corruption. Reported by Light-O-Rama.
Animated GIF images used in a Picture motion effect may flicker. Reported by user default.
Text in the title of the Playback window was changing appropriately when the window was docked to the main form, but not when it was undocked/floating. Reported by Light-O-Rama.
When the Playback window was undocked/floating and had focus, the space bar would not start sequence playback. Reported by Drew Hickman.
When double-clicking on a cell in a motion effect row, then cancelling out of the Motion Effect Generator, the playback window no longer displays a motion effect. Reported by Light-O-Rama.
When upgrading a sequence and using the Sequence Editor animation for the preview, for any RGB channels in the sequence that were not in the animation, S5 created an RGB channel prop as well as props for each of its red, green, and blue components. Now it correctly creates a single prop in this situation. Reported by Light-O-Rama.
When creating a new preview group, sub-props (props where the "Uses the same channels as" field is set) were allowed to be members of the group. Reported by Drew Hickman.
If a sequence had beat channels or loop rows, it was possible for the yellow box indicating the selected area to be incorrectly drawn and overlap between fixed rows at the top and the main part of the grid. Reported by Light-O-Rama.
In the Motion Effect Generator, you can now mute and un-mute during the middle of effect playback.
Clipboard files (.LCB file extension) created in S4 (or earlier versions) that contain RGB channel data now paste correctly into S5 RGB channels. Reported by Stephen Chapman via the help desk.
The LOR Hub program can now create SD cards with a full range of options, including triggers, filler sequences, starter sequences, etc. In a future release, SD card building will be removed from the Hardware Utility and the Simple Show Builder will be removed from the suite.
Previously there was no way to stop an SD card show from running on a particular day, except by using a workaround of setting the start and end times for a particular day the same. LOR Hub can now properly turn OFF a schedule for a particular day.
When creating an SD card in Advanced mode in Hub, a new option has been added to configure the MP3 Director's ports the same way as those ports are defined on the computer. This can help with ease of setup of MP3 directors.
LOR Hub has taken over all functions of the old Simple Show Builder program. In the next release this program will be removed from the suite. Instead, use LOR Hub to create your shows.
•Added support for group modify of "average time length of effects" and "skip inactive grid squares"
•Added the "Do Scene Thinning" option in the "Move or Scale Selected Effects" dialog box
•Added "Orientation" setting in the Preferences dialog box
•Added support to convert 6 channel star effects to white effects on RGB stars from other vendors (previously it only worked for the standard 200 pixel RGB star)
All 3 windows on the Motion Effect Generator now update simultaneously, which is also a performance improvement. Previously they could update slightly out of sync for very large props. Requested by Light-O-Rama.
If the user selects Create Playback Files from the menu and the sequence hasn't been saved, the user is now offered a chance to save it (without having to cancel, save the sequence, then try and create playback files again). Requested by user ndutton.
Enhancement: when opening a sequence, archived props will automatically be un-archived if a prop with the same name has been added back to the sequence's preview since the sequence was last opened. Same logic will also apply when you change the preview assigned to a sequence. Requested by Light-O-Rama.
Enhancement: more accurate conversion when assigning a different preview to an existing sequence. Requested by Light-O-Rama.
Performance improvements to the Picture motion effect. Requested by user jamills706.
In the New Animation Sequence dialog, show the sequence length as words, and give a warning when OK is clicked and the length is more than an hour. Requested by user Rabeiler.
In the sequence grid, the drop-down list of grid views would previously display views in the order they were created. Now, the system grid view (Show All Items) is listed first, and then user-created grid views are listed in alphabetical order. Requested by user Jade Rymkos.
Increased the maximum number of bulbs in a bulb shape to 999. Requested by users dibblejr and gsmith37064.
In the Paste Special dialog, you can now specify the spacing between horizontal copies. A negative value yields an overlap, a positive value leaves a blank space between each copy. 0 is always the default value (it is not remembered between uses). Requested by user spascall.
Added new "hold" effect, which freezes the state of the prior effect. For example, you can freeze and unfreeze a spiral effect to the beat of the music by alternating spiral and hold effects on the same motion effect row. The hold effect must be touching the prior effect to work. Requested by Light-O-Rama.
In Prop Definition, added "Arm Thickness" parameter to the Star shape. A value of 1.0 is the normal thickness. Smaller values make the arms thinner. Requested by Light-O-Rama.
New tab on Sequencer Preferences that allows the user to choose among 3 edit cursors. Previously, only the yellow pencil was available. Requested by user bdwillie.
"Custom Chase" options are now available on the toolbar via a new drop-down arrow next to the chase button. The chase options will also get saved with the sequence, and recalled the next time the sequence is opened. Requested by Jack Richter via help desk.
Add the "+" shortcut key for the Repeat function (to match SE). Requested by Light-O-Rama.
Added the Enter shortcut key to place an effect in the grid (to match SE). Requested by Light-O-Rama.
Added option in preferences (Channel Effects tab) to view fades as ramps. Requested by multiple users.
Added option in preferences (Channel Effects tab) to adjust background color of channel rows in the grid. Requested at Christmas Expo.
In Prop Defintion's layout tool for custom and advanced shapes, there is a new "Crop" function that removes extra rows and columns. Requested by Light-O-Rama.
Added Help buttons ("?" icon) to Preview Design, Prop Definition, Group Definition, and Custom Grid screens. Requested by Light-O-Rama.
Increased the max width and height on the SimpleShape effect to 1000% in order to allow shapes to expand beyond the prop boundaries. Requested by user Mike Baldwin.
Bug fix: in the sequence grid, right-clicking on a "member props" or "member groups" node and selecting "Hide Group Members" from the pop-up menu disabled further highlighting of prop names as the mouse pointer was moved. Reported by John Johnson Jr via help desk.
Bug fix: in rare cases the Sequencer could crash if 1) the LOR Control Panel was running when the Sequencer started, and 2) a Schedule was enabled or Show on Demand was running, and 3) the option to Control Lights when the Sequencer started was enabled. Reported by Jim Wright via help desk.
Bug fix: S5 Verifier checked for application files that don't exist in S5, which resulted in "Message Number 7" errors that were not really errors. Reported by stevehoyt, TitusCarnathan, richmuller and others.
Bug fix: when using music to control a slider in the Motion Effect Generator, the audio data was being pulled from the wrong part of the sequence. The effect used the correct audio data when placed in the sequence grid -- the error was only when the effect was displayed in the Motion Effect Generator. Reported by Light-O-Rama.
Bug fix: when you imported an S5 prop file in Preview Design, clicked the "Set Channels" button, then changed the name of the prop while setting channels, the resulting list of props and groups to lthe left of the design canvas would no longer be in alphabetical order. Reported by user ndutton.
Bug fix: if a sequence gets moved to another folder or to another computer and the media file is in the same folder as the sequence, then playback files created from the new location could point to the wrong folder for the media file. Reported by user ndutton.
Bug fix: when the sequence length was changed, the sequence was not marked as containing unsaved changes. Reported by Light-O-Rama.
Bug fix: in rare cases, effects could exist in sequences past the end of the sequence. When using playback files for such sequences, the Show Player would refuse to play the song with the message "ERROR STARTING SEQUENCE (Invalid end centisecond for last replacement event: 78195; channel is 55210 centiseconds)". Reported by NJ Malenke and stevehoyt.
Bug fix: if Holiday Lights Designer was enabled in S4 and then the user upgraded to S5, the Show Player would display errors in the log like "ERROR PLAYING SEQUENCE (Address in use Trace: UDP SetIntensity Trace: HandleIO)". Reported by Derek Flint via help desk.
Bug fix: certain combinations of removing and renaming props in a preview could leave a sequence unable to be opened (error message "An entry with the same key already exists"). Reported by Michelle Lovering via help desk.
Fix crash when Windows policy "System cryptography: Use FIPS compliant algorithms for encryption, hashing, and signing" is enabled. Reported by Dave Webb via help desk
The LOR SC485 serial port adapter (not USB) now works with the S5 Sequencer. Reported by several users via the help desk.
Fixed the online import of "Boscoyo ChromaStar 36 3 ring". Reported by Mike Baldwin via help desk.
Bug fix: in the Motion Effect Generator, double-clicking on a slider did not fully unlock it. Reported by Light-O-Rama.
Bug fix: in the Motion Effect Generator, effects with alpha transparency were not displayed correctly in the left and right windows. The combined window was correct. Reported by Light-O-Rama.
Bug fix: if the user right-clicked on a cell in the sequence grid, and then right-clicked on another cell in a different row, several cells in the clicked column would be selected. Reported by Light-O-Rama.
Bug fix: when doing Repeat, then Undo, then Redo, the Redo was done in the wrong place. Reported by Light-O-Rama.
Fixed a bug with clipboard files, where files created as part of the "Papagayo to LOR" process could not be pasted. Reported by Dennis Holliday via the help desk.
Bug fix: in the Control Lights window, unchecking a box for an enhanced LOR network or for DMX, did not actually stop output from going to those networks. Reported by Light-O-Rama.
•In LOR Hub and Hardware Utility, sequences with DMX Fades when written to the SD card could cause the MP3 director to go out of sync.
•LOR Hub was not able to properly create an SD Card schedule. The schedule would always revert back to the defaults instead of what the user specified.
•LOR Hub would crash if the user attempted to create an SD card show with no sequences in the create list.
•During installation, the Post Install process was not creating 3 new superstar visualization samples.
•In Superstar, text masks were not working in visualizations where some of the mask is outside of the matrix.
•In Superstar, fixed a bug where the white color control was not appearing if the only white that existed was in images.
•In Superstar, changed it so you can do "merge intensity data files" even in the demo version
•In Superstar, fixed a bug where scene pixels were getting clipped out if the clip region was on the right half of the wrap around screen
A "Where Used" function has been added to the File References dialog, so you can find the effect that uses a missing reference. Requested by Michael Lenbom via help desk.
In the Prop Definition screen, when defining a "Tree 360 Up & Over" shape using pixels, the shape diagram will now indicate the location of the first pixel on each string. Requested by Light-O-Rama.
The user now has control over how "smooth to fades" is applied with a new sub-menu: Sequence > Smooth To Fade Level. This setting controls whether adjacent effects are merged together or not. Previously, the level was fixed at the "mild" setting; however, with the mild setting it is impossible to create DMX intensities that are 2 steps apart (for example: 65, 63, 61). Requested by Drew Hickman.
Updated the pencil icon to be more visible, and moved the tip to the upper left. Requested by Ernie McAnally via help desk.
If the user had a Pro license, when they created Playback Files an intensity data file (.LID extension) was always created. Now an intensity data file is only created if the sequence has props that use DMX or Enhanced LOR networks. Requested by Light-O-Rama.
Added a "How Do I Get Started?" link at the top of the "Start Page". Requested by Light-O-Rama.
In the "Image Setup" dialog box, a new button was added called "Add +". The "Add+" button adds the current image to the image action, selects the next image, and bumps the time ruler selection forward. This makes it easy to add a series of images for an animation.
1.It enables our new MotionPak technology which allows you to modify LOR Sequence Store sequences for use with props the LOR Hardware Store will sell. The first props will be 'Singing Faces'
2.It is the replacement for Simple Show Builder. Simple Show Builder is still available in this release, however it will be removed in a future release. If you previously used Simple Show Builder you should move to Hub.
In future releases, Hub will continue to grow and will be taking over all 'show' type functionality including things like the Show Editor, Show Scheduler, and Building advanced SD cards for MP3 Directors from the Hardware Utility.
If the content of the Start Page extends beyond the bottom of the window, the vertical scrollbar that is displayed now spans the entire right edge of the window - making it easier to scroll. Reported by Light-O-Rama.
The first 4 items on the Windows menu have been renamed: "View Playback Window", "Viiew Motion Effects Window", "View Previews Window", and "View Control Lights Window". Also these items will only be shown if the respective window is currently hidden ("X" in the upper right corner of the window has been clicked). This should make it clearer what these menu items do, particularly the Control Lights item. Reported by Light-O-Rama.
If the content of the Control Lights window extends beyond the bottom of the window, a vertical scrollbar is now displayed. Reported by Light-O-Rama.
The Start Page can now be hidden, unhidden, and floated just like the Previews and Control Lights windows. Reported by Light-O-Rama.
Bug fix: the TextPE effect did not display the text specified by the user. Reported by user Dave Trollope via help desk.
Bug fix: if a sequence used video media and Loop At End was enabled for playback and video playback was set for full screen, the video window would often get resized instead of remaining full screen. Reported by user Bry.
When you right click on the sequence grid, there is a new sub-menu under Timing Marks > Insert Timing at Selection, with options for Left, Right, and Both. This will insert timing marks at the left and/or right edge of the grid selection. Reported by user Luke Kamp via help desk.
Bug fix: on Preview Design's Channel Conflict tab, clicking a column heading in the conflict list would crash the program. Now clicking a column heading sorts the table according to the values in that column. Reported by Light-O-Rama.
When dragging a favorite or subfolder in the Motion Effect Generator, the favorites tree will now auto-scroll when the cursor nears the top or bottom edge. Reported by user NJ Malenke via help desk.
Bug fix: when moving a timing mark with "Drag events with timings" enabled, the Sequencer could crash in some cases. Reported by user Peter Dusaitis via help desk.
Bug fix: the "Create an empty freeform timing grid" check box on the New Animation Sequence dialog did not actually create a freeform timing grid. Reported by Light-O-Rama.
You can now right-click on the Playback Window and change the brightness of the background image (if there is one). Reported by Light-O-Rama.
RGB aggregates with one or more sub-channels (red, green, or blue) left undefined, could cause the Sequencer to crash when modifying effects. Reported by user Keith Henrickson via help desk.
Added new dimming curves to the Prop Definition screen: Linear_30pct, Linear_40pct, PixelCurve_30pct, PixelCurve_40pct. Reported by user jamills706.
Windows Shell Commands get shared between sequences if you use File > Save As to create a new sequence. Specifying a new command from the revised screen will only affect the sequence that is open. Reported by user k6ccc.
In rare cases where 2 props in a preview have the same name, the entire preview file would not load at startup. Now the preview is loaded and a warning about duplicate names is shown on the "Other Warnings" tab of Preview Design. Reported by Light-O-Rama.
Fixed playback issues when sequences are arranged side-by-side. Reported by user NJ Malenke via help desk.
A "Copy to Clipboard" function has been added to the File References dialog. For sequences with many motion effect file references, this can allow you to paste the list of files into a spreadsheet or word processor for further analysis. Reported by user Stephen Chapman via help desk.
Bug fix: title bar of Playback Window was not showing the name of the current motion effect when one was clicked on in the sequence grid. Reported by Light-O-Rama.
During sequence playback, the Color Fade tool is now grayed out like the rest of the toolbar. Reported by Light-O-Rama.
If a comm port is unable to be opened, added a tip to the error message: "Make sure shows are disabled and the Hardware Utility is closed". Reported by user stevehoyt.
Added new menu items when right-clicking on the Preview Design canvas: Add, Modify, Copy, and Delete. Reported by Light-O-Rama.
Improvements when upgrading Pixel Editor previews and sequences to S5 for non-US customers -- problem occurred on PC's configured to use a comma as the decimal separator in numbers. Reported by user Niklas Adolfsson via help desk.
Bug fix: When using the space bar in the Tapper Wizard -- if you go one tap past when the music ends, the space bar defaults to the “exit” button and closes the wizard (thus erasing all of your “beats”). Reported by user Steve Warner.
Bug fix: the Sequencer could crash when the toolbar channel effect was set to DMX Intensity and you tried to add a motion effect. Reported by user Steve Warner.
Bug fix: clicking the Refresh button on the online prop import screen did not display the updated data correctly. Reported by Light-O-Rama.
In Archived Prop Management, added button to select all props with no effects. Reported by Light-O-Rama.
•The Post Install process failed to copy 3 new examples for Superstar.
•The configuration for PixCon16 MKII devices was incorrectly showing 32 ports.
•In Superstar, if the preview uses horizontal orientation and you go into "floating windows" mode, the program could crash.
•In Superstar, the first time beat marks are created they are created without issue. Creating beat marks a second time incorrectly deleted them.
•In Superstar, if you changed timings the program may not prompt you to save your work.
•In Superstar, when using Text Masks along with scenes or morphs, it was possible that the mask was not applied.
•In Superstar, when using a Text Mask or an Image Mask, if Layer Priority was disabled, foreground effects would be incorrect and background effects would not be rendered.
•In Superstar, if the program was launched from S5 changes would not be saved if "Save" or "Save As" was used to save the sequence as a .sup file.
•In Superstar, when using Autosequence effects, the displayed timings may be incorrectly changed to the most recently used Autosequence settings.
•In Superstar, when using Autosequence if "average the time length of effects" was selected then the last few seconds of an autosequence effect may not generate triggers.
•In Superstar, when using Autosequence if "Burst and Return" was used, there could be a compile issue. This happens most frequently with low sensitivity settings such as 1 or 2.
•In Superstar, when using Autosequence morphs with transparency set to transparent were not being saved properly.
•In Superstar, when shrinking using the pixel extender and smooth effects, the shrink did not occur properly.
•In Superstar, the "Center X,Y" control in the Smooth Effects dialog box the buttons were not oriented properly when creating a horizontal sequencing grid.
•In Superstar, if the pixel extender is enabled and a visualization with a sequencing grid was imported with a "max length" , a crash could occur.
•In Superstar, if the pixel extender is enabled and a sequence was being shunk, only half of the effects would get applied.
Some versions of the LOR S4/S5 uninstaller can leave behind unwanted programs in the user's Program Files(x86)\Light-O-Rama folder. This can lead to installation problems the next time the user tries to install the software. Registry Wipe can now clean those entries up.
1.The Sequencer starts about 20% faster. Reported by Light-O-Rama.
2.Improved the calculation time of Text and Picture effects. Reported by Light-O-Rama.
Countdown effect changes:
1.Added a "MM:SS" display option and allow a max of at least 1 hour. Reported by Light-O-Rama.
2.Text can now be positioned in both the X and Y directions. Forum request.
Changes to Preview Design:
1.you can now double-click on a prop in the design area to open its Prop Defintion. Reported by Light-O-Rama.
2.The "Tree 360 Spirals" shape could display an erroneous message regarding the number of folds when the number of revolutions was set to a large number. This message has been removed and the revolution limit restored to 25. Reported by Drew Hickman and user ukoberon. http://forums.lightorama.com/topic/46953-spiral-360-prop-tree-issue-512/
3.Created new "Cylinder Spiral" shape for spiral-wrapped tree trunks and columns. Reported by user jamills706. http://forums.lightorama.com/topic/46949-wrapped-tree-trunk-propmodel/
4.On the Prop Definition screen, if the diagram area was taller than it was wide, many of the shape diagrams would overflow. Now they are properly scaled. Reported by Light-O-Rama.
5.Bug fix: a prop made of pixels that uses the "Tree 360 Spiral" shape could crash the Sequencer. Reported by Light-O-Rama.
6.Bug fix: the Prop Definition window was expecting the "Arial Narrow" font to be installed, but that font is not on all computers. On some computers this could cause the program to show a continual stream of error messages. The program will now check if the font is installed before using it. Reported by user Norm Bowman (via help desk).
7.The "Tree 360 Up & Over" shape now supports folds in the string. When used with pixels, the layout has been redone to represent pixel strings that go up and over the top of the tree. Reported by Drew Hickman and Jesse Tryon.
8.If there are any unsaved changes in the Preview Design screen and you click the Cancel button or click the Windows "X" button to close it, then you will get a message confirming that you want to continue without saving the changes. Reported by user Gordon Varney (via help desk).
9.You can now delete props from the Channel Conflicts tab in Preview Design. Select Change Seleced Props > Delete Props. All of the actions on the Change Selected Props menu are also now available by right-clicking on the selected props in the Channel Conflict list. Reported by Light-O-Rama.
10.When copying a prop in Preview Design (Item > Copy), channels will no longer be renumbered if the "Uses the same channels as" field is set on the source prop. Reported by Light-O-Rama.
Changes to freeform play ranges:
1.Bug fix: when you were defining a freeform range for playback and you moved the cursor to the left - past the left edge of the grid - it cleared the selection. This made it difficult to select 0:00.00 as the starting point. Reported by Drew Hickman.
2.The following menu items have been added when you right-click on the timeline or the waveform (reported by user spascall):
a.Set Play Range Start - if no freeform play range exists, it creates a range from the selected point to the end of the sequence; otherwise it moves the start point of the existing range.
b.Set Play Range End - if no freeform play range exists, it creates a range from the beginning of the sequence to the selected point; otherwise it moves the end point of the existing range.
c.Clear Freeform Play Range - clears an existing freeform play range.
Do not allow channels to be copied in the "Show All Items" grid view. This grid view is system generated - items can be moved, but not hidden or copied. Reported by user daughjs.
In the sequence grid, when you right click on a channel name for a prop that has multiple strings, a new "Set Channel Name" option will appear. This capability will primarily help custom props with multiple strings which get channel names like "Horatio Hornblower: r64 c31". The channel name will be stored with the preview, so it will apply to all sequences that use that preview. Reported by Robert Brescia.
In the Skew All and Skew Selection commands, the maximum offset has been increased from 10 seconds to 600 seconds. Also, the user will now have the option of skewing the current timing grid or all freeform timing grids. Reported by user NJ Malenke.
Bug fix: changes made to the sequence while calculations are occurring (icon in the upper left is spinning), might not be reflected during preview playback. Reported by user k6ccc.
After clicking on a slider in the Motion Effects Generator, you can now fine-tune the value using the left or right arrow keys. If the slider is unlocked, shift-left-arrow and shift-right-arrow can be used to change the ending value. Reported by Drew Hickman.
When you right-click on the timeline or the waveform and select "Zoom In" from the menu, the zoomed sequence grid is now centered on where the right-click took place. Reported by Light-O-Rama.
In rare cases, a preview could get saved that had a prop with an invalid circuit number (like 0). In prior versions, this would result in a popup error message as the Sequencer opened; and if the preview were subsequently opened in Preview Design could result in a crash. Going forward there is no popup message when the program is opened. The preview can then be opened in Preview Design and the error will be reported on the "Channel Conflicts" tab - where it can be corrected. Reported by Light-O-Rama.
Bug fix: you are no longer allowed to drag beat channels into the list of preview props and vice versa. Reported by Light-O-Rama.
The 3 versions of the chase tool (intelligent, by prop, and by row) have been condensed into 2: regular chase and custom chase. Regular chase is the same as intelligent chase (chase by prop when the first row is a motion row, and chase by row for anything else) with the addition that the selected area for the chase is now cleared. For a custom chase, the user is prompted whether they want to chase by row or prop, and whether the selected area should be cleared. A new keyboard shortcut shift-H initiates a custom chase. Custom chase is also accessible from the right-click menu. Reported by user spascall.
When exporting the grid configuration and "Show All Items" is the current grid view, the user will now get a warning stating that "Show All Items" is a system-generated view and will not be included in the export file. Reported by Drew Hickman.
In the Paste Special window, the "All the way to the end of" drop-down box now includes the last item in the selection and the last row in the grid view. The last row in the grid view is now the default. Reported by user spascall.
Bug fix: motion effects on props should override effects on groups that they are a member of. However, that was not happening in all cases. Reported by user John Trp (via help desk).
Bug fix: the Fill tool would display the message "Trying to fill between effects, but the row is empty!" when the sequence row was not empty. Reported by user lkcubsrule.
Bug fix: Ampersands (&) in prop names would not display correctly in the sequence grid. Reported by Light-O-Rama.
When playing back a sequence to real lights and when saving playback files, the Sequencer now checks if motion effects have been placed on props connected to an LOR network that is not enhanced. If so, then the action is cancelled until the condition is fixed. Reported by Light-O-Rama.
The music is only supposed to play one time when you click the play button in the Motion Effect Generator. However, due to a bug, if the loop button on the toolbar for the sequence was enabled, it would cause the music to repeat in the Motion Effect Generator as well. Reported by Light-O-Rama.
The Motion Effect Generator now has a mute button so users can turn off the music while creating their motion effect. Reported by NJ Malenke.
When using the Max Intensity, Min Intensity, Fade Up, or Fade Down tools, the message "'Motion effect' is selected on the toolbar, but no motion effect is currently displayed in the playback window. Would you like to create an effect using the Motion Effect Generator?" will now only get displayed when motion effect rows are part of the selection. If the effect shown on the toolbar is "motion effect" but only channel rows are selected, then the toolbar effect is changed to the ON effect. Reported by Drew Hickman.
The checkbox to enable or disable looping of effects in the Motion Effect Generator has been replaced by a toggle botton (press on, press off). Also, the loop icon shown there and on the sequence toolbar will now show a red slash through it when disabled. Reported by Light-O-Rama.
Bug fix: when attempting to open a playback file (.play.lms), the program would display an error message, then go ahead and open the file anyway. Now no attempt is made to open the playback file after the error is displayed. Reported by Light-O-Rama.
Fixed the File References dialog so that long sequence names, media file names, and preview background file names wrap if they extend beyond the width of the window. Reported by Light-O-Rama.
•Several new options and effects have been added to Superstar's Auto Sequence tool including effects 'Folding Ricochet', 'Snake Up/Down', along with options to 'Skip Inactive Grid Squares' as well as 'Average the Time Length of Effects'.
•The Sequencer now sends the current timing grid to SuperStar when inserting a SuperStar effect. This allows SuperStar to display the same timings as the Sequencer.
•Exporting as intensity data could cause the program to crash
•In the Auto Sequence dialog box if the user did not select one of the 8 custom colors, a message is now displayed.
•When saving in the Demo version, the file added to the recent files dialog was incorrectly specified as ',supe.sup'.
•When saving in the Demo Version, the suggested filename was incorrectly defaulted to '.supe.sup'.
•In some cases, opening a valid .supe file would cause an error stating the file was not created on this computer.
•Improved export speed of sequences that use large Visualizations
•Increased the number of images allowed from 1500 to 3000.
•When automatic modification of Star Scenes occurred, it was incorrectly changing the archive status of the file.
•Increased the width of every 5th long tick mark on the edge of the sequence grid
•In sequences with effect groups, after a 'select all' effect groups could no longer be expanded.
•Increased available memory for both 32 and 64 bit systems.
•The number of channel elements has increased from 8 million to 50 million.
•When using Single Step, if the stop button was pressed the first selected effect was not made active. This could lead to a warning or error.
•Writing large images could cause the program to crash.
•The number of fonts has been increased to 30 to allow for user created fonts to be used.
•While using the Pixel Extender, if the Layer Priority feature was active pixels were extended too far.
•When using the Move or Scale effects tools while in wrap around mode, some effects were not wrapped properly.
Sequence grid row height:
1.Bug fix: if the user repeatedly shrunk the row height in the sequence grid, they would reach certain sizes where some prop/channel names did not get displayed. Now names are always displayed, regardless of the row height. Reported by user ndutton.
2.Enhancement: depending on the row height, the Sequencer would choose one of 3 font sizes to display prop/channel names with. Now it will choose among 4 font sizes - a new one was added when the row height is extra tall. Reported by Light-O-Rama.
In Preview Design, renamed "Channel Conflicts" tab to "Channel Conflicts (and bulk change tool)" to better reflect its functionality. Reported by Light-O-Rama.
Audio wizard changes:
1.Bug fix: when the VU Wizard was set to analyze only part of the song, it would still insert timing marks and/or channel effects for the entire song. Reported by Light-O-Rama.
2.The default timing grid shown in the Beat, VU, and Tapper wizards is now the one currently selected in the sequence grid. Reported by Light-O-Rama.
3.Improved performance when the Apply button is clicked in the Beat, VU, and Tapper wizards. Reported by Light-O-Rama.
4.Bug fix: when clicking the "Start" button on the Tapper wizard, typing the space bar did not produce taps. Reported by Drew Hickman and NJ Malenke.
Moved menu item Sequence > Audio Wizards > Add Beat Channel to Sequence > Add New > Beat Channel. On the sequence grid's right-click menu, the Audio Wizards > Add Beat Channel item was removed. Added item to the Grid View menu: Add New > Beat Channel. Reported by user Drew Hickman.
Fixed multiple issues with the Renumber Strings dialog (accessed by going to Preview Design, Channel Conflicts tab, Change Selected Props > Renumber Strings). Also added a "Reverse Order" button to this dialog. Reported by user k6ccc. http://forums.lightorama.com/topic/46721-editing-channel-assignments-information/
The "Other Warnings" tab in Preview Design will now display a warning when the channel assignments for a master prop and sub-prop are out of sync. A sub-prop has the "Uses the same channels as" field populated in the Prop Definition screen. Reported by user k6ccc. http://forums.lightorama.com/topic/46721-editing-channel-assignments-information/
Renamed the opening "Sequences" tab page to "Start Page" to better reflect its purpose. Reported by Light-O-Rama.
Enhancements to the Prop Definition window:
1.All shape parameters are now displayed in a single column list and a scroll bar will be displayed if the list does not fit in the available space.
2.There are no longer separate tabs for the "Custom" and "Advanced" shapes. The grid to edit those shapes is now accessed from a button which opens a separate window -- giving the user much more screen space to edit custom props.
3.A thumbnail view is now displayed for Custom and Advanced props in the lower portion of the Shape section.
4.The delete key can now be used to clear cells on the grid when editing a Custom or Advanced shape.
5.The last shape you used to create a new prop is now remembered and set as the default the next time you create a prop.
6.The Save and Cancel buttons were moved to the upper left corner to be consistent with the Preview Design window.
New shapes in Prop Definition:
1.Tree 360 panels. This can model large commercial trees that are assembled by tiers, and those tiers are broken into panels/branches. The shape assumes each panel has its own set of channels and that every panel is lit the same way. Requested by user Drew Hickman.
2.Tree 360 tiers. Also known as "Z trees". This shape does not support RGB pixels. Requested by user spascall.
3.Sphere and Cylinder shapes. These can be configured to display 1, 2, 3, or all 4 quadrants (vertical sections). The Tree 360 Wedges shape was also updated with a parameter to choose the number of quadrants it displays. Requested by user stevehoyt and others. http://forums.lightorama.com/topic/46771-how-to-define-prop-for-tree-shaped-like-a-globe/
If there are no existing previews, the Upgrade Sequence screen now disables the choose existing preview option. Reported by Light-O-Rama.
The sequence upgrade process now does a better job of handling inconsistent settings on RGB channels. Previously, some situations could cause the Sequencer to crash. Reported by user Val Bennett.
During the sequence upgrade process, warnings about subsequence channels now include the channel name. Reported by Light-O-Rama.
Adjusted the size and layout of the New Animation Sequence and New Musical Sequence dialogs so they display correctly when the "Visual Effects" tab of Window's Performance Options dialog is set to "Adjust for best performance". Reported by user John Hall.
Adjusted the wording of items in Preview Design's "Add New Item" dialog. Reported by Light-O-Rama.
Changes to motion effects:
1.Removed the align left, center, and right buttons for the Text effect -- as they did not have any effect on actual lights. Reported by user k6ccc. http://forums.lightorama.com/topic/46834-feature-request-horizontal-position-offset-in-motion-effects/
2.Added TextPE effect that exactly replicates theÂ S4Â Pixel Editor's text effect to improve sequence upgrades. Adjustments to text effects in upgraded sequences are no longer required. Note there are now 2 text effects in S5: "Text" and "TextPE". Reported by Light-O-Rama.
3.Renamed the "Full Length" option in the Movie effect to "Movie Length Matches Sequence Length". Reported by Light-O-Rama.
4.Bug fix: when inserting a new motion effect, the Motion Effect Generator window could be calculating the effect "None" (blank screen) even though the selection in the drop-down box showed a different effect. This only occurred when Sequencer Preferences > Motion Effects > "When opening, initialize from the current toolbar effect and color" was unchecked. Reported by Light-O-Rama.
5.Bug fix: in some cases the bulb size slider control on the Motion Effects Generator could disappear. Reported by Light-O-Rama.
6.Bug fix: the scanner effect could cause an error during effect calculations and result in the play buttons not being enabled. Reported by Chris Reynolds and Eric Brown.
7.There is no longer a delay when you first open the Motion Effects panel until thumbnail images appear. Reported by Light-O-Rama.
On the grid's toolbar, the Motion Effects and SuperStar tools are now only visible when the user has a PRO level license. Reported by Light-O-Rama.
Added a warning when trying to use the Fill tool on an empty row. Reported by Light-O-Rama.
If the current toolbar effect is set to "Motion Effect" when the Color Fade tool is selected, the toolbar effect is now automatically changed to "On". Reported by Light-O-Rama.
•Added "Snake Up" and "Snake Down" as movement options in the Auto Sequence dialog box
•Added "skip inactive grid squares" option in Auto Sequence dialog box
•Added "Average the Time Length of Effects" option in Auto Sequence dialog box
•Fixed a bug where an encrypted file from previous versions would not read in if it has groups or timings in it.
•Added a check for "Full Range" color mode if launched from a SuperStarRequest. If in "Full Range" mode, SuperStar forces "Balanced" mode and adjusts all the color values to be 100 or less.
•Made it so every 5th long tick mark on the edges of the sequencing grid is thicker.
•Fixed a bug where if you had effect groups in a sequence and you did "select all" then you could no longer expand the effects in the effect groups
•Doubled the amount of memory SuperStar can use This prevents memory errors when compiling large sequences.
•Fixed a bug where writing out a large image could cause the program to crash.
•Fixed it so the Auto Sequence movement options work properly with pixel speeds other than 1.00
Initial production release of S5 ShowTime Designer Pixels.